Camco Wright Stain System

  • $ 120.20


For Automated and Manual Staining of Blood Smears
Classic, Traditional Textbook Coloration

The unique combination of these products has been developed for the use in automated and manual staining of blood smears for hematological studies. These special 5-step processes (featured on the Camco® Wright Stain label) provides stained blood smears of classic tradition with textbook colors utilizing our Camco® Wright Stain, Camco® Fixative and Camco® Wright Stain Buffer pH 7 .15 or pH 6.8

Camco Wright Stain System

400, CAMCO®  Wright Stain

A highly refined, modified and purified alcoholic Wright Stain solution. This specially formulated stain makes analysis of the smear much easier. Size is 3.78 L - 1 gallon.

WARNINGThis product can expose you to Methanol, which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to P65Warnings.ca.gov.

Please contact the office at 800.525.6262 to purchase this product. 

Camco Wright Stain System

401, CAMCO® Fixative

A methanol-based fixative to set the blood smears as the first step in the 5-step processes. Also may be used for any fixing purposes where Methanol fixing is needed. Size is 3.78 L - 1 gallon.

WARNINGThis product can expose you to Methanol, which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to P65Warnings.ca.gov.

Please contact the office at 800.525.6262 to purchase this product. 

Camco Wright Stain System

402, CAMCO® Wright Stain Buffer pH 7.15

Each 4.4 g vial is enough to prepare 1 gallon of pH 7.15 buffer solution for use in the 5-step staining process. The buffer is helpful with the development of the correct, clear nuclear color scheme. 10 Vials - 4.4 g each

Information Sheet:
400 401 & 402
Camco Wright Stain System

SDS: 400 SDS: 401 SDS: 402

Directions:

Solution Ingredients Percent Volume
(For 500mL)
Procedure
1 Fixative 100 % 500mL A. Fix slide by dipping into solution 1 for a few seconds - then AIR DRY COMPLETELY.
2 Wright Stain
Fixative
70 %
30 %
350mL
150mL
B. Dip slide into solution 2 for two minutes.
3 Wright Stain
Buffer (7.15pH)
20%
80 %
100mL
400mL
C. Dip slide into solution 3 for five minutes.
4

Buffer (7.15pH)
Water

16.7 %
83.3 %
84mL
416mL
D. Dip slide into solution 4 for forty seconds.
5 Buffer (7.15pH) 100 % 500mL E. Dip slide into solution 5 for thirty seconds.

Alternate Directions for Use in Automated or Manual Method:

Solution Ingredients Percent Procedure
1 Fixative 100 % A. Place slide in Fixative for 30 seconds.
2 Wright Stain 100 % B. Place slide in Wright Stain for 3 minutes.
3 Buffer Diluent* 100 % C. Manufacture Buffer Diluent for step 4.
*Buffer Diluent: A mixture of 23% of either 6.8 or 7.15 pH buffer solution and 77% Deionized Water.
(i.e. Buffer Solution 30mL + Deionized Water 100mL)
4

Wright Stain Buffer Diluent

16.7 %
83.3 %
D. Place slide in Stain-Buffer Diluent mixture for 6 minutes.
(i.e, Wright Stain 20mL + Buffer Diluent 100mL)
5 Deionized Water 100 % E. Rinse with Deionized Water and then let slide dry.

General Notes 

    1. When product/procedure work as expected at the beginning and then later results are not as high quality, change ALL solutions, as they are probably contaminated. It usually occurs during continuous, heavy use and when jars are left open (exposed) to the air. Exposure to moist air causes precipiation.
    2. Make sure all slides are clean prior to making the blood smear, if not, stain will not absorb properly onto the smear.
    3. Whenever automated staining machines are used, it is very important not to allow any chemical to dry in the delivery tubes. The lines utilized in steps 1, 2, and 3 must be rinsed with fixative (Methanol) and the lines used in steps 4 and 5 must be rinsed with distilled water to insure proper delivery of all process chemicals.

**For In Vitro Diagnostic Use.**

 

Sale

Unavailable

Sold Out